RETRACTABLE SHOWER SEAT – FRONT MOUNTING | 170

Technical specs(pdf): 170

Seat folds up into cabinet. Fabricated of 12 gauge stainless steel, exposed surfaces have a satin finish. Seat has reinforced channels. Wall sub frame furnished, with welded on masonry anchors.
Sub Frame Opening:
15" x 15" x 2 3/4" (380 x 380 x 70 mm).

FRONT MOUNTING POST TYPE TOILET TISSUE HOLDER | 111

Technical specs(pdf): 111

Fabricated of 18 gauge 1 1/4" (32 mm) OD stainless steel type 304 with satin finish. Flange is 3" (76 mm) diameter x 1/8" (3 mm) thick and has 3 countersunk holes for front mounting.

Overall Size
4 1/2" x 3 3/4" (115 x 95 mm) projection.

SQUARE RECESSED TOILET TISSUE HOLDER – REAR MOUNTING | 110-1

Technical specs(pdf): 110-1

Fabricated of 14 gauge type 304 stainless steel with satin finish exterior, glass blasted satin finish interior 4 1/2" (115 mm) deep accommodates one standard toilet tissue roll. Flange is 7" (180 mm) square. Hidden contraband causes roll to project from holder allowing detection. Two "T" nuts welded on back for rear mounting.

Overall Size
7" x 7" (180 x 180 mm).

SQUARE RECESSED TOILET TISSUE HOLDER - FRONT MOUNTING | 110-13

Technical specs(pdf): 110-13

Same as 110-1 except with front mounting holes.

RECESSED TOILET TISSUE HOLDER – REAR MOUNTING | 110

Technical specs(pdf): 110

Fabricated of 16 gauge type 304 stainless steel, satin finish exterior, glass blasted satin finish interior. 4 1/2" (115 mm) interior depth accommodates one standard toilet tissue roll. Hidden contraband causes roll to project from holder allowing detection. Two "T" nuts welded on back for rear mounting.

Overall Size
7 1/4" (185 mm) diameter.

FOLDED TOILET TISSUE HOLDER - FRONT MOUNTING | 117

Technical specs(pdf): 117

Holder is 14 gauge type 304 stainless steel, satin finish. Open design for detection of contraband. Provided with 4 mounting holes for front mounting.

Overall Size
4 3/4" x 9" x 2 3/4" (120 x 230 x 70 mm).

FRAMED MIRROR - REAR MOUNTING | 101

Technical specs(pdf): 101

Frame 14 gauge type 304 stainless steel with satin finish, corners welded and ground smooth. Unit provided with fiberboard backing and 6 "T" nuts welded on back for rear mounting. Specify glazing suffix required (see page 31 for legend) and also specify wall thickness if greater than 6" (150 mm).
see chart for standard sizes and surfaces.

Overall Size
12" x 16" x 5/8" (305 x 405 x 16 mm).

FRAMED MIRROR – FRONT MOUNTING | 104

Technical specs(pdf): 104

Unit consists of wall mounting plate fabricated of 7 gauge type 304 stainless steel with 4 countersunk mounting holes and 8 tapped holes. Formed mirror fabricated of 18 gauge type 304 stainless steel with #8 mirror polish finish provided with 8 dimpled holes through integral frame and 1/4 - 20 x 1/4" TORX head screws for securing to wall mounting plate.

Overall Size
10 1/16" x 11 9/16" x 7/16" (255 x 290 x 11 mm).

ONE PIECE FRAMED MIRROR WITH ROUNDED CORNERS – FRONT MOUNTING | 107

Technical specs(pdf): 107

One piece 18 gauge type 304 stainless steel formed mirror with #8 mirror polish finish, integral frame, rounded corners and 6 mounting holes.

Overall Size
12" x 16" x 1/4" (305 x 405 x 6 mm).

ONE PIECE FRAMED MIRROR WITH ROUNDED CORNERS – REAR MOUNTING | 108

Technical specs(pdf): 108

Same as 107 with 6 "T" nuts welded on back for rear mounting

FRAMED MIRROR – FRONT MOUNTING | 105

Technical specs(pdf): 105

Similar to 101, but front mounting, furnished with TORX vandal resistant 1/4 - 20 x 2" (150 mm) machine screws.

REAR MOUNTING RECESSED SOAP DISH | 140

Technical specs(pdf): 140

Soap dish 16 gauge stainless steel type 304 with satin finish. One piece drawn construction with beveled trim and embossments for air circulation and drainage. Unit has two "T" nuts welded on back for rear mounting.

Overall Size
7 3/8" X 6" (215 x 155 mm).

SECURITY GRAB BAR (REAR MOUNTED) | 160

Technical specs(pdf): 160

Tubing 18 gauge and flanges 1⁄8“ (3 mm) thick stainless steel type 304 with satin finish. Closure plate is 1⁄8" (3 mm) thick. All welded construction. Unit has 3 Threaded Rods in Welded Studs on each flange for rear mounting.

Overall Size
24" (610 mm)

SECURITY GRAB BAR (REAR MOUNTED) | 161

Technical specs(pdf): 161

30" (760 mm)

Overall Size
30" (760 mm)

SECURITY GRAB BAR (REAR MOUNTED) | 163

Technical specs(pdf): 163

36" (915 mm)

SECURITY GRAB BAR (REAR MOUNTED) | 166

Technical specs(pdf): 166

42" (1070 mm)

SECURITY GRAB BAR (REAR MOUNTED) | 168

Technical specs(pdf): 168

48" (1220 mm)

SECURITY GRAB BAR (FRONT MOUNTED) | 165

Technical specs(pdf): 165

Tubing 18 gauge and flanges 1⁄8“ (3 mm) thick stainless steel type 304 with satin finish. Closure plate is 1⁄8" (3 mm) thick. All welded construction. Unit has 3 holes through each flange for front mounting.

Overall Size
24" (610 mm)

SECURITY GRAB BAR (FRONT MOUNTED) | 162

Technical specs(pdf): 162

30" (760 mm)

SECURITY GRAB BAR (FRONT MOUNTED) | 164

Technical specs(pdf): 164

36" (915 mm)

SECURITY GRAB BAR (FRONT MOUNTED) | 167

Technical specs(pdf): 167

42" (1070 mm)

SECURITY GRAB BAR (FRONT MOUNTED) | 169

Technical specs(pdf): 169

48" (1220 mm)

Overall Size
48" (1220 mm)

SURFACE MOUNTED TWIN SECURITY TOILET PAPER DISPENSER | 8436-2S

Technical specs(pdf): 8436-2S

The security toilet paper dispenser, constructed of 18 gauge satin finish type 304 stainless steel alloy 18-8, holds two (2) 1800 sheet tissue rolls. The internal baffle provides intermediate support for locking the spindle bar with a padlock (not supplied) for enhanced security. Structural assembly of body components is of welded construction. Theft and vandal resistant spindle bar with welded collar stop is supplied.